ENGLISH
ADEBRIL
2C
BICOMPONENT POLYURETHANE VARNISH
VL2C (glossy) VS2C (semi-glossy)
Particularly indicated for varnishing various kinds of wood
floors , or wood surfaces in general. It gives to the surface
elasticity, fullness and excellent resistance to scratching.
HOW TO USE:
VARNISHING AND
AUXILIARY PRODUCTS
PREPARATION OF THE SURFACE
The wood floor must be previously treated with MAXIFONDO SF
2C (see technical sheet). The surface to be treated must be dry,
with humidity between 8 – 12%. Ambient temperature between
15 and 25°C, relative humidity not greater than 75%. It must be
sanded with 180 grain sandpaper. After sanding, clean the entire
surface with a vacuum and then with an anti-static cloth.
APPLICATION
Make sure the product is at ambient temperature and mix it
accurately before use. Prepare only the necessary amount of
product for the application using clean containers. Mix uniformly
with a clean stick the two components (1 part component A and
1 part component B) and allow the mixture to begin reacting for
about 10 minutes before application. Apply a uniform layer of
product on the surface using a roller or brush. After about 12
hours under normal conditions a second coat of ADEBRIL 2C can
be applied on the previously sanded surface use 180 grain
sandpaper and entirely cleaned surface with a vacuum and then
with an anti-static cloth. Check that the humidity of the wood is
between 8 and 12%, the ambient temperature between 15 and
25°C and the relative humidity is not greater than 75%. Always
use adequate personal protective equipment. Always consult the
MSDS sheet of the product.
ADESIV s.r.l. - Sede amministrativa e operativa: Via delle Rose, 31 - Sede legale: Via S. Patrizio, 33 - 36061 Bassano del Grappa (VI) - ITALY
Tel.: +39(0)424-566 406 - Fax: +39(0)424-566 473 - Sito: www.adesiv.it - E-mail: [email protected]
The company complies to quality management system standard UNI EN ISO - 9001:2008
certified by SGS Italia S.p.A., certificate no. IT07/0491.
TECHNICAL DATA (at standard conditions):
Aspect:
Viscosity (@20°C; Ford #4):
Gloss Value 60°:
(UNI 10726)
Dryness (%):
Catalysis ratio (A:B):
Pot life (hours):
Coverage (g/m2):
Dust free (minutes):
Application conditions (°C):
TreaTable (hours):
Utilizable (days):
Application/Tools:
Tool cleaning:
Packaging:
Storage (months):
liquid
14 – 16
VL2C: >80
VS2C: 60 - 70 30 – 45
1:1
2
80 – 100
60 – 70
+15 - +25
24
7
Roller, brush
GR7, when the product is still fresh
10 l containers (5 l component A + 5 l component B)
temperature between +5°C and 6
+25°C
Do not apply in damp areas
Limitations of use:
Aerate the area during application, avoiding drafts
Make sure the temperature of the product is 20°C before applying
Always use an adequate mask and protective gloves
Solvent based
RECOMMENDED PAINTING CYCLES:
MAXIFONDO SF2C + ADEBRIL 2C
PREPARATION OF THE SURFACE
The wood floor must be very smooth and sanded with 150-180
grain sandpaper and free of any parts that may detach such as
oils, waxes and silicon. The surface to be treated must be dry,
with humidity between 8 – 12%. Ambient temperature between
15 and 25°C, relative humidity not greater than 75%. After
sanding, clean the entire surface with a vacuum and then with an
anti-static cloth.
APPLICATION
Make sure MAXIFONDO SF 2C is at ambient temperature and mix
ADESIV s.r.l. - Sede amministrativa e operativa: Via delle Rose, 31 - Sede legale: Via S. Patrizio, 33 - 36061 Bassano del Grappa (VI) - ITALY
Tel.: +39(0)424-566 406 - Fax: +39(0)424-566 473 - Sito: www.adesiv.it - E-mail: [email protected]
The company complies to quality management system standard UNI EN ISO - 9001:2008
certified by SGS Italia S.p.A., certificate no. IT07/0491.
it accurately before use. Prepare only the necessary amount of
product for the application using clean containers. Mix uniformly
with a clean stick the two components (1 part component A and
1 part component B), and allow the mixture to begin reacting for
about 10 minutes before application. Apply a uniform layer of
the product on the surface using a roller or brush. After about
12 hours under standard conditions a coat of ADEBRIL 2C can be
applied on, the previously sanded with 180 grain sandpaper and
entirely cleaned surface with a vacuum and then with an
anti-static cloth. Prepare only the necessary amount of ADEBRIL
2C for the application using clean containers. Mix
homogeneously with a clean stick the two components (1 part
component A and 1 part component B) and allow the mixture to
begin reacting for about 10 minutes before application. Apply a
uniform layer of product on the surface using a roller or brush.
After about 12 hours under standard conditions a second coat of
ADEBRIL 2C can be applied on the surface previously sanded
with 180 grain sandpaper and entirely cleaned with a vacuum
and then with an anti-static cloth.
NOTES
ADESIV s.r.l. Guarantees that the information in the present sheet are given to
the best of its experience and technical-scientific knowledge; however, it is not
liable for results obtained as application conditions are out of its control. It is
recommended to always verify the suitability of the product for the specific
case. The present sheet annuls and substitutes any previous sheet.
ADESIV s.r.l. - Sede amministrativa e operativa: Via delle Rose, 31 - Sede legale: Via S. Patrizio, 33 - 36061 Bassano del Grappa (VI) - ITALY
Tel.: +39(0)424-566 406 - Fax: +39(0)424-566 473 - Sito: www.adesiv.it - E-mail: [email protected]
The company complies to quality management system standard UNI EN ISO - 9001:2008
certified by SGS Italia S.p.A., certificate no. IT07/0491.