BROADBAND ROUTER WIRELESS 150N 150 MBPS MANUALE NI-707538 I TA L I A N O CONTENUTO DELLA CONFEZIONE 4 C A R AT T E R I S T I C H E T E C N I C H E 4 GAMMA DI APPLICAZIONI 4 I N S TA L L A Z I O N E H A R D W A R E 5 CONFIGURAZIONE DEL ROUTER 6 WPS 11 CE/FCC 12 GARANTIE 15 BROADBAND ROUTER WIRELESS 150N 150 MBPS Grazie per aver acquistato questo router 150N. Se vuoi collegare diversi PC e condividere lo stesso accesso ad Internet, avrai bisogno di un componente aggiuntivo per collegare i PC fra loro. Questo router ti consente di creare una rete wireless, in modo rapido ed efficiente. 3 I TA L I A N O CONTENUTO DELLA CONFEZIONE Prima di iniziare l’installazione, controlla che tutte le parti necessarie siano presenti. La scatola dovrebbe contenere: - Router 150N Wireless Adattatore di alimentazione da 5V CD con manuale completo Manuale utente 1A C A R AT T E R I S T I C H E T E C N I C H E Basso consumo energetico, 1.1W Protocollo wireless 802.11n Compatibile con IEEE802.11g e IEEE802.11b Supporta WEP, WPA/WPA2, TKIP / AES IEEE802.1x autenticazione 150 Mbps velocità di trasferimento dati 1x 2dBi aerea Radio pulsante ON / OFF Gestione basata sul web Supporta: IP Dinamico, IP Statico, PPPoE 1 x WAN, 4 porte LAN RJ-45 UTP Server NAT e DHCP incorporato Supporta: VPN pass through Indipendente dal sistema operativo GAMMA DI APPLICAZIONI Questo router ti consente di creare una connessione Internet wireless a banda larga su più computer. Oltre ad una con nessione Internet condivisa, puoi anche creare una rete che colleghi diversi PC. Collega il modem ADSL alla porta WAN del router e dopo qualche secondo il LED WAN si accenderà. Adesso puoi collegare i PC. Una volta avviati i PC, il LED interessato si accenderà. 4 I N S TA L L A Z I O N E H A R D W A R E Non appena hai collegato il router all’adattatore di alimentazione, il LED di alimentazione (Verde) si accenderà e i LED link/act lampeggeranno una sola volta. Gli altri LED (Verdi) si accenderanno non appena una delle porte UTP sarà connessa al computer. Quando i dati vengono trasferiti da un computer all’altro, i LED inizieranno a lampeggiare. INDICATORI LED Nome PWR WLAN WAN LNK/ACT LAN 1-4 LNK/ACT Azione del LED ON Descrizione Il router è acceso e correttamente alimentati. ON Wireless funzione WPS è abilitata. OFF Rete wireless è spento. Lampeggia Wireless LAN attività (il trasferimento o la ricezione di dati). ON Porta WAN è collegata. OFF Porta WAN non è connesso. Lampeggia WAN attività (il trasferimento o la ricezione di dati). ON Porta LAN è collegata. OFF Porta LAN non è connesso. Lampeggia LAN attività (il trasferimento o la ricezione di dati). 5 PANORAMICA DEI COLLEGAMENTI SUL RETRO DEL ROUTER CONFIGURAZIONE DEL ROUTER Una volta collegato il router correttamente, puoi iniziare a configurarlo. Per alcuni provider avrai bisogno di qualche informazione aggiuntiva, quale un nome utente e una password. Apri il browser Internet, digita il seguente indirizzo nella barra degli indirizzi http://192.168.2.1 e premi su “Enter” Verrà visualizzata la seguente schermata. Per accedere al router digita “admin” come nome utente e ”1234” come password, quindi clicca su “OK” Dopo aver cliccato su “OK”, verrà visualizzata la schermata di configurazione del router. 6 Clicca su “Quick Setup” e quindi su “Next”. Seleziona la tua connessione Internet, e dopo che il provider ti avrà fornito nome utente e password, che serve per le connessioni via cavo, seleziona l’opzione PPPoE. Se hai già una connessione ADSL con un modem ADSL, seleziona “Cable Modem”. L’indirizzo IP viene assegnato automaticamente dal tuo provider, e verrà quindi utilizzato dal router. Se hai un IP Dinamico, clicca su “Cable Modem” per passare direttamente alla schermata “Dynamic IP” 7 Se hai una connessione PPPoE, digita il tuo nome utente nel campo “Account Name” e la password fornita dal provider nel campo “Password”. Quindi clicca su “OK”. Per cambiare le impostazioni wireless, andare su “Wireless” e cliccare su “Basic Settings” Se non vuoi fare nessuna modifica, clicca su “Apply”. 8 Una volta cliccato su “Apply”, ritornerai alla schermata “Basic Settings”. Adesso che il router è stato configurato, è importante che la funzione wireless del router sia protetta. Se non proteggi il router, le persone nelle vicinanze saranno in grado di utilizzare la tua connessione Internet. Nella schermata principale del router, cliccando sull’opzione “Wireless” “Security Settings” verrà visualizzata la seguente schermata. Attiva la funzione “Enable Wireless Settings”. Seleziona WPA2 (AES) come tipo di sicurezza. Per la funzione “Pre-Shared Key” inserisci il tuo codice di rete e prendi nota del codice poiché ti servirà per creare una connessione cliente wireless con il router. Una volta inseriti tutti i dettagli, clicca su “Apply”. Verrà visualizzato il seguente messaggio: “You may press CONTINUE button to continue configuring other settings or press APPLY button to restart the system to make the changes take effect.” Fare clic su “Apply” per riavviare il router. 9 Utilizza questo spazio per annotare le impostazioni del tuo router. IMPOSTAZIONI WIRELESS SSID : …………………………….. Frase di riconoscimento PSK: …………………………….. NB Per ottenere il massimo dal tuo router, consulta il manuale completo che si trova sul CD-ROM. 10 CONFIGURAZIONE WPS WPS (Wi-Fi Protected Setup) funzione consente di aggiungere un nuovo dispositivo wireless a una rete esistente in fretta. WPS può essere utilizzato solo se il router supporta anche questa funzione. Premere il pulsante sul router e sulla scheda e attendere fino a quando appare la schermata seguente. Quindi fare clic su “Finish”. La connessione WPS possono essere stabiliti anche facendo la connessione nel programma di utilità software. Ciò consentirà inoltre di utilizzare un codice PIN. Per ulteriori informazioni su WPS, si prega di leggere il manuale completo sul CD. 11 C E M A R K WA R N I N G This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. NATIONAL RESTRICTIONS This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: COUNTRY RESTRICTION REASON/REMARK Bulgaria None outdoor use and public service General authorization required for France Outdoor use limited to Military Radiolocation use. 10 mW e.i.r.p. within the Refarming of the 2.4 GHz band has band 2454-2483.5 MHz been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None general authorization is required If used outside of own premises, Luxembourg None General authorization required for network and service supply (not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Please don’t use the product outdoors in France S’il vous plaît ne pas utiliser le produit à l’extérieur en France. 12 F C C S TAT E M E N T This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) 2) This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. 13 Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. F C C R F R A D I AT I O N E X P O S U R E S TAT E M E N T: This device has been tested for compliance with FCC RF Exposure (SAR) limits in the typical laptop computer configuration and this device can be used in desktop or laptop computers. This device cannot be used with handheld PDAs (personal digital assistants). This device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance. 14 GARANTIE Salvo indicazione contraria, tutti gli articoli venduti con il marchio ICIDU hanno una garanzia di 10 anni. Non viene fornita alcuna garanzia o assistenza per il software o per le batterie ricaricabili. Eventuali reclami durante il periodo di garanzia possono essere fatti solo tramite il rivenditore dove è stato acquistato il prodotto. Le caratteristiche del prodotto possono subire delle modifi che senza preavviso. Tutti i prodotti ICIDU soddisfano gli attuali standard e le direttive in materia di sicurezza e ambiente. Per ulteriori dettagli, visitate il nostro sito Web www.icidu.com ICIDU è un marchio registrato. Tutti li altri marchi e diritti ad essi collegati sono e rimangono di proprietà del legittimo proprietario. © Copyright 2011 ICIDU Tutti i diritti riservati 15